Posted by Mike Levine | April 19, 2011

By Mark Williams for PickupTrucks.com
You've seen and read about the JK-8 Independence project truck
and its conversion kit Jeep recently unveiled as part of a coordinated
herd of secret build projects being brought to the 2011 Easter Jeep
Safari in Moab, Utah, but we wanted a closer look. Chrysler's Mopar
parts and accessories division has made big promises about turning a
four-door Wrangler Unlimited into a pickup truck, so we jumped at the
chance to get up close and personal with the vehicle.
To review, the kit will consist of 18 parts that include a short
50-inchbed floor, half a hardtop, a lower bulkhead, inner and outer rear
body panels, several brackets and two bedrail extensions. As you might
expect, a host of body, rollbar and floor modifications are also
necessary, not to mention some serious welding if you want the looks of
the JK-8. The kit will be available from Mopar by July 4; pricing will
not be announced until right before it goes on sale.

The JK-8 Independence has somewhat awkward proportions. Its regular
cab looks too fat, and the bed looks too small for the wheelbase. This
particular specialty vehicle sports a 4.5-inch lift and 35-inch-tall
tires. The regular cab configuration offers a small amount of storage
room behind the seats and does allow for some seat travel for
long-legged drivers. There are no changes to the Unlimited's swing-out
rear door (now a door gate) so this pickup would have to skip tailgate
party duty.
The Independence also seems a little odd in that Jeep is inviting
those interested in this kind of model to load the vehicle like a
pickup, but it makes no accommodations for improving the payload
capacity of the vehicle beyond the stock Unlimited.

To date, Mopar has no plans to offer a heavier or progressive rear
coil spring or some stronger bump stops (maybe overload springs?) to
help improve the rather meek SUV-like payload capacity. For reference, a
fully clothed stock Wrangler Unlimited can weigh around 4,100 pounds
with a maximum gross vehicle weight rating around 5,400 pounds. In the
most optimistic scenario, the rear coils should be able to handle a
little more than 1,000 pounds of payload without trouble. Of course, if
you make too many modifications, install a few parts and leave your
luggage in the passenger seat, you could cut that number in half.
As you might expect, from behind the wheel, there isn't much
difference between this and a standard Unlimited in drive feel or
responsiveness. Our JK-8 Independence had a manual transmission and the
3.8-liter V-6, rated at 202 horsepower and 237 pounds-feet of torque ?
certainly not a monster, but adequate for a smaller vehicle like this,
especially one that's likely to be doing some rock crawling in low-range
four-wheel drive.

We'd expect the Mopar package to make the rear section feel a bit
lighter on a stock vehicle, possibly creating a stiffer, jumpier feel to
the back end when on rougher roads. As it was, with the heavier wheels
and tires on this special project vehicle, and a huge piece of General
Grabber and steel wheel hanging off the back end of the Jeep, it was
impossible to determine any lightness or imbalance in the chassis.
Additionally, this vehicle had a stronger front Dana 44 axle and a set
of burly front and rear Mopar JK (this particular Wrangler model
designation) HD bumpers.
For our tastes, the wheelbase needs to be longer to give the bed more
length, and something needs to be done about the meager payload
capacities, even if this kit is just an appearance package. With that
said, if this is going to be the placeholder for a couple of years for
the coming Jeep pickup truck, with Mopar getting all the glory for
offering a unique body package, we think we can live with that ? for a
couple of years.

As previously mentioned, pricing won't be out for a while, but we'd
guess it will be below AEV's Brute pickup truck conversion kit. On the
plus side, Jeep already has all the stamping paid for because it has an
export-only military model, called the J8, that uses the same side and
floor body panels.
One interesting note: Jeep had a huge display right in the middle of
town at the Easter Jeep Safari, where it built an entire shop that put
together a bolt-on version of one of these JK-8s in front of a large
audience in about two hours. We're guessing it might take us a little
longer.
